Hilomast Compressor Kits for Hilomast Pneumatic Masts

Hilomast compressors are air cooled, oil-less and of the diaphragm type. They have steel cases and are powered by electric motors. All models incorporate a pressure controlled switch to maintain the correct mast working pressure. They are quiet, maintenance free and assembled from components that have a proven reliability over many years.

Compressor Type	Approx. rate of mast extension Metres per minute
	NH Series	NK Series	NL Series	NX Series	NY Series
NC1	7.2	4.2	2.6	1.7	-
NC2	13.5	8.1	4.8	3.2	1.7
NC3	-	18.1	10.8	7.5	3.9

To calculate time to fully extend mast: The height of mast is divided by rate e.g. For NL/12 mast with NC/2 Compressor - Extension Time = 12 ÷ 4.8 = 2.5 minutes. The time to reach max. pressure is approx. 2 x Extension Time e.g. 5 minutes.

NC1 Compressor
NC2 Compressor
NC3 Compressor

The NC1 compressor is the smallest and simplest in the Hilomast range. They are portable and thus suitable for field applications. The units are supplied complete with a single hose and mast connector. The mast is retracted by a manual exhaust valve on the front of the unit, enabling full control from inside a vehicle or building. Although designed primarily for the NH and NK Series masts, they will perform satisfactorily with the NL Series, when the speed of extension is not important.

Specification
NC1/230 for 220/240v AC	Output: 17 litres/minute at 0.7Kg/cm2 Max. Pressure: 1.8 Kg/cm2 Weight: 13.2 Kgs. Size: 300 x 320 x 210mm high
NC1/12 For 12v DC supply NC1/24 For 24v DC supply	Output: 17 litres/minute at 0.7Kg/cm2 Max. Pressure: 1.8 Kg/cm2 Weight: 8 Kgs. Size: 290 x 145 x 210mm high

The NC2 compressor has all the features of the NC1 compressor and gives approximately twice the output. An additional feature is a single switch that controls both power supply and an electrically operated exhaust valve.

The units are supplied with two hoses, one for connection to mast and one for exhaust air and drainage. This feature is very useful for vehicle installation, as it drains the moisture collected in the mast from the compressor. The NC2 compressors are ideally suited for the NL Series masts but will work equally well with the NK and NX Series.

Specification
Max. Pressure: 1.8 Kg/cm2 Weight: 15 Kgs. NC2/230 for 220/240v AC	Output: 34 litres/minute at 0.7Kg/cm2 Size: 330 x 320 x 220mm high
Single phase supply	Current: 1 amp
NC2/12 For 12v DC supply	Current: 14 amps
NC2/24 For 24v DC supply	Current: 8 amps

The NC3 compressor is the largest in the Hilomast range. Although designed for NX and NY Series masts, they can be used to operate smaller masts where a faster rate of extension is required (see table) They have the same type of switch and hose arrangement as the NC2 compressor.

The units are supplied to meet standard conditions but there is capacity within the system to accommodate customers specialised electrical or pneumatic control requirements.

Remote controls are available as an optional extra.

Specification
Max. Pressure: 1.4 Kg/cm2 Weight: 34 Kgs. NC3/230 for 220/240v AC	Output: 65 litres/minute at 0.7Kg/cm2 Size: 400 x 395 x 370mm high Overload Protection: MCB
Single phase supply	Current: 2 amps
NC3/12 For 12v DC supply	Current: 30 amps
NC3/24 For 24v DC supply	Current: 16 amps

Remote Control Options

RC1

Three position switch for NC2/NC3
Enables mast to be extended, retracted or held at any point
Handheld for DC powered compressors or mounted for DC or AC
ABS enclosure and 4m cable

These switches should be ordered with the compressor but can be supplied in kit form for retro-fitting to non-remote units.

RC2

Three button relay interfaced unit has separate commands to extend, hold or retract mast
IP65 die cast housing and 4m cable
Weatherproof plug and socket
Primarily designed for external low voltage DC control of NC2 and NC3 AC driven compressors but may be used to control a relay interface for DC driven compressors

These remote controls must be ordered with the compressor.